GREPhysics.NET
GR | # Login | Register
   
  GR0177 #85
Problem
GREPhysics.NET Official Solution    Alternate Solutions
This problem is still being typed.
Electromagnetism}Resistivity

This is a baby circuits problem once one calculates the net resistance.

Recall that resistance is related to length and area by R=\rho l/a.

Thus, the resistance of the thin and long wire is R_{tl}=\rho 2L/A, while the resistance of the fat and short wire is R_{fs}=\rho L/(2A).

The resistors are in series, and so the equivalent resistance is R_{eq} = \rho L/A(2+1/2)=5\rho L/(2A).

Plug that into Ohm's Law to find the current \Delta V = I R_{tot} = 8-1=7. Thus, I=14A/(5\rho L).

To find the potential at the junction, use Ohm's Law again to get V_{junction}=1+IR_{fs}. Chunking out the algebraic expressions, one gets 2.4 V, as in choice (A0.

See below for user comments and alternate solutions! See below for user comments and alternate solutions!
Alternate Solutions
BerkeleyEric
2010-10-03 11:38:34
Since the resistance is directly proportional to the length and inversely proportional to the area, we know that the longer wire is four times as resistant as the shorter one. This means that the voltage drop is four times as much for the longer wire, so it is \frac{4}{5}\ \left(7\ V\right). Subtracting this from 8.0 V gives the answer, (A).Alternate Solution - Unverified
BerkeleyEric
2010-10-03 11:38:02
Since the resistance is directly proportional to the length and inversely proportional to the area, we know that the longer wire is four times as resistant as the shorter one. This means that the voltage drop is four times as much for the longer wire, so it is \frac{4}{5}\ \left(7\ V\right). Subtracting this from 8.0 V gives the answer, (A).Alternate Solution - Unverified
94709
2007-10-29 23:04:05
You can calculate current although one doesn't have to. This is just a voltage divider.

R_1=\rho\frac{2L}{A}, R_2=\rho\frac{L}{2A}, \Delta V=7 Volts.

Therefore,

V=7\times\frac{\rho}{\rho}\times\frac{\frac{L}{2A}}{\frac{2L}{A}+\frac{L}{2A}}=\frac{7}{5}=1.4

Since the base is 1V, the potential at the dividing segment is 2.4V.
Alternate Solution - Unverified
Comments
Dudeleb
2016-10-27 15:16:34
here is a fun little rhyme to help you remember the resistance of a wire. Resistance = RHO RHO RHO YOUR BOAT L OVER A! RESISTANCE RESISTANCE RESISTANCE LIFE IS BUT A DREAM (of an electron traveling down some conducting material). The rest is math. Plug and chug. Like a beer. Am I RIGHT!? Ah man. This test is making me crazy. Cheers all. NEC
ChildAtPlay
2012-04-16 04:14:14
R = rho * L / A. Rho is the same for both wires.
Setting L = 1, A = 1:

Wire 1: R1 = 2L/A = 2

Wire 2: R2 = L/2A = 1/2

Rtotal = R1 + R2 = 2.5.

deltaV for wire 2 is R2/Rtotal = 0.5/2.5 = 0.2.

The voltage drop across wire 2 is 20% of the total voltage drop (Kirchoff).

Voltage @ junction = 1V + 0.2 * (8V-7V) = 1V + 1.4V = 2.4V.
NEC
BerkeleyEric
2010-10-03 11:38:34
Since the resistance is directly proportional to the length and inversely proportional to the area, we know that the longer wire is four times as resistant as the shorter one. This means that the voltage drop is four times as much for the longer wire, so it is \frac{4}{5}\ \left(7\ V\right). Subtracting this from 8.0 V gives the answer, (A).Alternate Solution - Unverified
BerkeleyEric
2010-10-03 11:38:02
Since the resistance is directly proportional to the length and inversely proportional to the area, we know that the longer wire is four times as resistant as the shorter one. This means that the voltage drop is four times as much for the longer wire, so it is \frac{4}{5}\ \left(7\ V\right). Subtracting this from 8.0 V gives the answer, (A).Alternate Solution - Unverified
grae313
2007-11-01 10:17:36
Alternately, (and this is essentially equivalent 94709's solution, but involves simpler calculations, IMO), once you have the two resistances for the two wires, you can realize that R_1 = 4R_2 which means that the ratio of the voltage drops in each wire segment has to be 1:4, or:

\frac{\Delta V_1}{\Delta V_2} = \frac{4}{1} and also

\Delta V_1 + \Delta V_2 = 7

easy math to arrive at the answer.
grae313
2007-11-01 10:17:59
ack, I meant to classify this as an alternate solution
NEC
94709
2007-10-29 23:04:05
You can calculate current although one doesn't have to. This is just a voltage divider.

R_1=\rho\frac{2L}{A}, R_2=\rho\frac{L}{2A}, \Delta V=7 Volts.

Therefore,

V=7\times\frac{\rho}{\rho}\times\frac{\frac{L}{2A}}{\frac{2L}{A}+\frac{L}{2A}}=\frac{7}{5}=1.4

Since the base is 1V, the potential at the dividing segment is 2.4V.
94709
2007-10-29 23:14:15
eh, you might not be checking this site any more, but thanks a lot, yosun.
Alternate Solution - Unverified
keflavich
2005-11-10 22:38:30
There are a few typos here. I=\frac{14A}{5(pL)}, you left out the 5. That 0 at the end should be a ')'.

But also... where does the 1 come from in V=1+IR_{fs}?
yosun
2005-11-10 22:49:04
keflavich: thanks for the typo alert; the typo has been corrected.

the 1 comes from the fact that the potential at the end of the fatter wire is 1V, and thus the voltage across the junction is just the voltage at the end of the fat wire plus the current times the resistance of the fatter wire. (i tend to leave off the units to avoid confusion with variables)
Richard
2007-10-29 10:07:52
A perhaps conceptually easier approach would be to simply find the potential difference across the first wire, and then subtract it from the potential at the end of the thin wire. In my view, this is consistent with how you went about finding the current...

8-(\frac{2\times 14}{5})=2.4
jmason86
2009-07-09 23:54:25
Alternatively, you could have done \delta v=IR \Rightarrow 1-8 = ... yielding the same value for I, but negative.
Then following along Yosun's line (where he implied V=V_2 + IR_2), we now have instead, V=V_1 + IR_1 where I is now negative. Plug in to get 8-\frac{28}{5} = \frac{12}{5}

I was kind of confused by the above response that Yosun gave using the fatter wire for everything... so I decided to try flipping it around to make sure it still works... and it does :)

Cheers
Fixed Typos!

Post A Comment!
You are replying to:
You can calculate current although one doesn't have to. This is just a voltage divider. R_1=\rho\frac{2L}{A}, R_2=\rho\frac{L}{2A}, \Delta V=7 Volts. Therefore, V=7\times\frac{\rho}{\rho}\times\frac{\frac{L}{2A}}{\frac{2L}{A}+\frac{L}{2A}}=\frac{7}{5}=1.4 Since the base is 1V, the potential at the dividing segment is 2.4V.

Username:
Password:
Click here to register.
This comment is best classified as a: (mouseover)
 
Mouseover the respective type above for an explanation of each type.

Bare Basic LaTeX Rosetta Stone

LaTeX syntax supported through dollar sign wrappers $, ex., $\alpha^2_0$ produces .
type this... to get...
$\int_0^\infty$
$\partial$
$\Rightarrow$
$\ddot{x},\dot{x}$
$\sqrt{z}$
$\langle my \rangle$
$\left( abacadabra \right)_{me}$
$\vec{E}$
$\frac{a}{b}$
 
The Sidebar Chatbox...
Scroll to see it, or resize your browser to ignore it...